To select a Power-Up Option, hold down the button indicated for at least 1 second while turning the Meter on. The manual is easy to decipher, even for non-electricians, and is in several languages. . If the features that the 117 offers fit your demands, there is no better option than the 117. If you do not have an account yet, please apply here and get direct access to specialist engineers. This includes the 117 as well as the Fluke 323 amp clamp meter, which can measure current up to 400A. The building quality is superior to other brands in the same price range and even warrants the slightly higher price compared to other multimeters you might consider.
This small multimeter has an ergonomic chassis, easily held in the palm of your hand, and a trademark large display area that is backlit. This unit comes with a 9V battery included. If an equivalent calibrator is used, it must meet the accuracy specifications shown in Table 1. Dirt or moisture in the input terminals can distort meter readings. Replace the battery as soon as the low battery Use only Fluke Part Number 803293.
Though also fairly light, it is no slouch, being both sturdy and very durable, built as it is with quality materials. As part of the 320 series, the 323 is renowned for its usability and can also measure voltage and resistance. This feature can literally be a life saver, and although most electricians have the tools to do this, having it included in your multimeter can save you lots of time. Please note: if you are ordering a re-reeled item then the order cut-off time for next day delivery is 4. Accessible by way of a single screw without removing the holster, it has direct-to-board terminals and a sturdy design. You can pick one of these up at the same time. This gives it the ability to analyze outlets, appliances, control panel boards and switch gear, both single and three phase.
Schematics 4 Free Service manuals, schematics, documentation, programs, electronics, hobby. Remove the Meter from the protective yellow holster. Though the Fluke 117 multimeter can be operated with one hand, it is compatible with the ToolPak magnet hanger for true hands-free usage. However for safety and compactness, the current shunt in the Meter is specified for 10 A continuous, 20 A overload for up to 30 seconds. Remove the battery and battery door. There are two sensitivity modes, Hi and Lo — good for roughly five inches and one inch respectively.
Some items are non-cancellable and non-returnable. Performance Test Steps Function Frequency Display switch position Input value sine wave Lower Limit Upper Limit 300 mV 50 Hz 0. Caution The circuit board is extremely susceptible to contamination. The following information is included:. It has automatic voltage selection. To avoid damaging the housing, never apply solvents to the Meter. This manual applies to all actions that could cause bodily harm or death.
Everything is intuitively laid out as with other models. This document provides the information necessary to calibrate and verify the performance of the Fluke Model 110, 111, and 112 multimeters. The cables for the test probes have a little bit of wiggle room on each end, which will extend the life expectancy for the leads. Periodically wipe the case with a damp cloth and mild detergent. The recessed calibration button is located under the calibration seal on the back of the Meter.
This is a highly capable tester, boasting a high level of accuracy, quality and durability. This relatively cheap product line offers four digital multimeters for different specific purposes. Another feature that will prove extra helpful for electricians is the This means that the Fluke 117 will recognize ghost voltage and prevent false positives. It does make for a good backup meter for service technicians in the field, however, as well as for diagnosing faults in the auto industry. For those people, the more extensive and expensive might be the better choice.
On the inside, the engineering holds up to critical standards, and the quality of engineering is much higher than other multimeters that are built in China. This calibration information applies to all three models. Although the test leads will do for most people, one way to get a much better experience with the Fluke 117 is to upgrade the test leads. Although this series is made in China, there is no letup in the build quality and it is a cheaper alternative to most Flukes. Let them help you identify product alternatives, source additional technical data and find answers to your technical questions. This can be adjusted with or without gloves. With its sensor on the head of the tester, you can quickly ascertain voltage through a cable or wall, as with a voltage stick.